Home
Jaltest Diagnostics
WHERE TO BUY JALTEST?
DIAGNOSTICS
TELEMATICS
ISOBUS
OEM
MILITARY
UNIVERSITY
MY ACCOUNT
Cart
REQUEST INFORMATION
Online Catalog   ONLINE CATALOG

Coverage

FIND OUT ALL OUR COVERAGE
All coverage
What are you looking for?
TRUCK TRAILER BUS LIGHT COMMERCIAL VEHICLE MANUFACTURER
OHW - HEAVY EQUIPMENT OHW - COMPACT EQUIPMENT STATIONARY ENGINE MULTI-PURPOSE VEHICLE
MHE - MATERIAL HANDLING EQUIPMENT
INBOARD ENGINE OUTBOARD ENGINE STATIONARY ENGINE JET SKI

/ AGV / TRACTOR / JOHN DEERE / 6R SERIES

ADAS system
ADAS system
Manual Process
Manual Process
Fault code reading
Fault code reading
Measure Values
Measure Values
Components Actuation
Components Actuation
ECU Data
ECU Data
Parameters
Parameters
Calibration
Calibration
Reset
Reset
Real-time data monitoring
Real-time data monitoring
Wiring diagram
Wiring diagram
Vehicle Technical Data
Vehicle Technical Data
Vehicle maintenance
Vehicle maintenance
Diagnostics function with help available
Diagnostics function with help available
SMART Guides
SMART Guides
Model wiring diagrams
Model wiring diagrams
Knorr-Bremse Diagnostics
Knorr-Bremse Diagnostics
Central Services
Central Services

Manual Process: Manual diagnostics process of the system through display codes, blinking codes…

Fault code reading: Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading.

Measure Values: It displays on the screen the values of the different sensors connected to the ECU. It depends on each system.

Components Actuation: They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system.

ECU Data: These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system.

Parameters: Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed.

Calibration: Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly.

Reset: This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics.

Real-time data monitoring: Technical information of the system indicating the checking values, descriptions, graphics, charts…

Wiring diagram: Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier.

Vehicle Technical Data: Technical information of vehicles including all the engine technical data, tightening torques, capacities, graphics and other checking values…

Vehicle maintenance: Section in which the maintenance intervals are displayed, indicating the operations to be performed on the vehicle, and through which the reports that make the customers management easier for the repair shop can be obtained.

SMART Guides: Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions!

Model wiring diagrams: Wiring diagrams by model show the relation between all the electrical components of a vehicle. They complement the technical information of the wiring diagrams included in the license and provide detailed specifications about the interconnection of electrical elements, connections to other control units and intermediate connectors.

Knorr-Bremse Diagnostics: An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality

Central Services: Exclusive diagnostics functionalities with remote assistance

6R SERIES

General vehicle information: Technical information of vehicles including all the engine technical data, tightening torques, capacities, graphics and other checking values… Section in which the maintenance intervals are displayed, indicating the operations to be performed on the vehicle, and through which the reports that make the customers management easier for the repair shop can be obtained.
System ADAS system Manual Process Fault code reading Measure Values Components Actuation ECU Data Parameters Calibration Reset Real-time data monitoring Wiring diagram SMART Guides Knorr-Bremse Diagnostics Central Services
Antitheft EIC, Immobilizer Control Unit ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Audio system CRU, Radio ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Auxiliary brakes PLC, Parking lock unit ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Central computer CCU, Body computer ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Central computer FCC, Control unit, front module ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Climate HVAC ATC, Automatic Temperature Control ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Climate HVAC ETC, Climate Control System ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Electronic module AIC, Electronic Module ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Electronic module CLC, Cabin module ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Electronic module CSM, Switches modular system ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Electronic module OIC, Control system for the vehicle configuration ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Electronic module TEC, Tractor Electronic Control Unit (TECU) ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Electronic module VLC, Lighting, operator's controls ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Engine ECU HPCR (Level 21 - Interim Tier 4 / Stage III B), Electronic Diesel Control, Common Rail ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Engine ECU HPCR (Level 23 - Interim Tier 4 / Stage III B), Electronic Diesel Control, Common Rail ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Engine ECU HPCR (Level 33 - Tier 4F/5 - Stage IV/V), Electronic Diesel Control, Common Rail ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Engine ECU HPCR (Level 34 - Tier 4F/5 - Stage IV/V), Electronic Diesel Control, Common Rail ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox GPM, Transmission regulation system ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox PTA (AutoPowr- IVT), Transmission ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox PTD (DirectDrive), Transmission ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox PTQ (PowrQuad-Plus / AutoQuad-Plus / CommandQuad), Transmission ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox TIA, Transmission regulation system ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox TID, Transmission regulation system ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox TIN, Transmission regulation system ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Gearbox TIQ, Transmission regulation system ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems HCC, Hydraulic lift ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SB1, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SB2, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SB3, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SB4, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SB5, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SB6, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SBJ, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SBK, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SBL, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SBM, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SBN, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SCC, Control panel for spool valves ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Hydraulic systems SCO, Remote Hydraulic Controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Instrument cluster PDU, Instrument cluster - display ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Lighting RLC, Roof lights ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Power take-off PAP, Power take-off ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Power take-off PTF, Front power take-off ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Power take-off RPT, Rear power take-off ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Steering XMC, Auto-guidance system, GPS ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Steering XSC, Auto-guidance system, steering controller ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Suspension CSC, Cabin suspension management system ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality
Suspension SFA, Suspension management system in the front axle ADAS system Manual diagnostics process of the system through display codes, blinking codes… Allows to read the ECU failure memory by providing the user information about the fault codes detected in it. This function allows the user to carry out the clearance of the fault code memory; logically if the fault code is active, it will be detected again by the ECU and it will be displayed in the following fault code reading. It displays on the screen the values of the different sensors connected to the ECU. It depends on each system. They are the direct tests that can be done with the system components. For example, actuate an ABS modulator, activate the suspension solenoid valves in order to raise or low the vehicle chassis... They are active diagnostics which, for example, enable tests for engines to calibrate their state, like the cylinder balance, cylinders cut-out or compression, depending on each system. These are the technical data of the ECU, serial number, software version, manufacturer's reference, etc. It depends on each system. Some ECU can operate with different configurations. With this option you can copy configurations and parameters to the control unit, so control units can be programmed in its first installation. For certain systems even the modification of some parameters not affecting the vehicles security is allowed. Some systems ask to calibrate some components for its correct operation. The best examples are the electronic suspensions, for which the reference values must be stored so the ECU can perform the function correctly. This point refers to the reset of the control unit maintenance counters. If the maintenance operations are completed but the maintenance alarm is not canceled, the warning message referring to maintenance will keep on. It has nothing to do with the clearing of the fault codes from the memory, which is part of diagnostics. Technical information of the system indicating the checking values, descriptions, graphics, charts… Detailed diagram of the system containing added information on configuration, components, locations and notes which make the diagnostics tasks easier. Jaltest offers the key to increase efficiency in repair processes. The SMART guides take the user directly to the correct step, according to the vehicle conditions, fault codes and registered parameters. Say good-bye to unnecessary actions! An additional subscription to the Knorr-Bremse Diagnostics module is required to access this functionality

ARE YOU INTERESTED IN JALTEST DIAGNOSTICS?

CONTACT COJALI USA INC.
Cojali USA Inc.
2200 N.W. 102 Avenue, #4B
Doral, Florida 33172, USA

TECHNICAL SUPPORT TEAM
+1 305 960 7651
Call for free:
+1 800 975 1865
customersupport@jaltest.com
Facebook X Instagram YouTube TikTok Linkedin Threads
Cojali
   Copyright © 2024 Cojali S.L. All rights reserved
COJALI
COMPANY
This page uses our own and third-party cookies to improve the navigability and accessibility of our web site and to optimize the user experience. You can click on "Settings" to obtain more information about them and to set or refuse their use.
aenor aenor
European Regional Development Fund
Book a Demo
Anchor Bottom